 |
 |
 |
 |
 |
 |
Sains Malaysiana 53(1)(2024): 135-148
http://doi.org/10.17576/jsm-2024-5301-11
Modification on Drying Chamber Wall of Spray Dryer towards Better
Yield
(Pengubahsuaian
pada Dinding Kebuk Pengeringan Pengering Semburan ke arah Hasil yang Lebih Baik)
NIK FARHAN NAZMI NIK
ABD RAHMAN, HASLANIZA HASHIM*, SAIFUL IRWAN ZUBAIRI & MOHAMAD YUSOF MASKAT
Department
of Food Sciences, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi,
Selangor, Malaysia
Diserahkan: 5 Oktober 2023/Diterima:
12 Januari 2024
Abstract
Spray drying is a widely used
industrial process that converts liquid or slurry feed materials into dry
powder or granules and it commonly shrouded with the stickiness problem. This
study was carried out by response surface methodology (RSM) to minimize fouling
during the spray drying process by optimizing the condition of the drying
chamber wall of the spray dryer. The concentration (%) and exposure time (min)
of polytetrafluoroethylene (PTFE) were examined as
independent variables in order to modify the dryer wall. Responses including
flux adhesion weight, product recovery, hygroscopicity,
and moisture content of the powder were evaluated. Statistical analysis showed
that experimental data were best fitted into a quadratic polynomial model with
regression coefficient values greater than 0.75 for all responses. The optimum
conditions in reducing fouling were discovered at PTFE concentration of
17.27% and PTFE exposure time of 6 min. These
conditions would result in low flux adhesion weight (35.28 mg), high product recovery
(39.38%), low hygroscopicity (6.08%) and low moisture content (7.97%). The observed outcomes aligned with the predicted values,
affirming the suitability of the model in improving the flowability of the spray drying process.
Keywords: Fouling;
polytetrafluoroethylene; response surface methodology; spray drying
Abstrak
Pengeringan semburan ialah proses perindustrian yang digunakan secara meluas yang menukar bahan suapan cecair atau buburan kepada serbuk kering atau butiran dan ia biasanya diselubungi dengan masalah kelekitan. Penyelidikan ini dijalankan dengan kaedah permukaan respons (RSM) untuk meminimumkan kotoran semasa proses pengeringan semburan dengan mengoptimumkan keadaan dinding kebuk pengeringan pengering semburan. Kepekatan (%) dan masa pendedahan (min) politetrafluoroetilena (PTFE) telah dikaji sebagai pemboleh ubah tak bersandar untuk ubah suai dinding kebuk pengeringan tersebut. Tindak balas termasuk berat lekatan fluks, hasil produk, higroskopisiti dan kandungan lembapan serbuk telah dinilai. Analisis statistik menunjukkan bahawa data uji kaji adalah paling sesuai dengan model polinomial kuadratik dengan nilai pekali regresi melebihi 0.75 untuk semua tindak balas. Keadaan optimum bagi mengurangkan kotoran telah ditemui pada kepekatan PTFE ialah sebanyak 17.27% dan masa pendedahan PTFE selama 6 minit. Keadaan ini akan menghasilkan berat lekatan fluks yang rendah (35.28 mg), hasil produk yang tinggi (39.38%), higroskopisiti yang rendah (6.08%) serta kandungan kelembapan yang rendah (7.97%). Hasil yang diperhatikan sejajar dengan nilai yang diramalkan, mengesahkan kesesuaian model dalam meningkatkan aliran proses pengeringan semburan.
Kata kunci: Kaedah permukaan respons; kotoran; pengeringan semburan; politetrafluoroetilena
RUJUKAN
Ahmad, I. & Nguyen, L.T. 2017. Water-glass transition temperature profile during spray drying of sugar-rich foods. In Glass Transition and Phase Transitions in Food and Biological Materials, edited by Ahmed, J. John Wiley and Sons Inc. pp. 239-249. Andrade, I. & Flores, H. 2004. Optimization of spray drying of roselle extract (Hibiscus sabdariffa L.). In Drying Proceedings of the 14th International Drying Symposium, Sao Paulo, Brazil (pp. 597-604).
Ashokkumar, S. & Adler-Nissen, J.
2011. Evaluating non-stick properties of different surface materials for
contact frying. Journal of Food Engineering 105(3): 537-544.
Avram, M., Avram, A.M., Bragaru, A.,
Ghiu, A. & Iliescu, C. 2008. Plasma surface modification for selective
hydrophobic control plasma surface modification for selective hydrophobic
control. Romanian Journal of Information Science and Technology 11(4):
409-422.
Braga, V., Guidi, L.R., de Santana,
R.C. & Zotarelli, M.F. 2020. Production and characterization of
pineapple-mint juice by spray drying. Powder Technology 375: 409-419.
Bowden, F.P. & Tabor, D. 2001. The Friction and Lubrication of Solid. Oxford: Oxford University Press. Chang, L.S., Tan, Y.L. & Pui,
L.P. 2020. Production of spray-dried enzyme-liquefied papaya (Carica papaya L.) powder. Brazilian Journal of Food Technology 23: e2019181.
Daza, L.D., Fujita, A.,
Fávaro-Trindade, C.S., Rodrigues-Ract, J.N., Granato, D. & Genovese, M.I.
2016. Effect of spray drying conditions on the physical properties of Cagaita (Eugenia
dysenterica DC.) fruit extracts. Food and Bioproducts Processing 97:
20-29.
Dhanumalayan, E. & Joshi, G.M.
2018. Performance properties and applications of polytetrafluoroethylene (PTFE)
- A review. Advanced Composites and Hybrid Materials 1: 247-268.
do Carmo, E.L., Ribeiro Teodoro,
R.A., Campelo, P.H., de Abreu Figueiredo, J., Botrel, D.A., de Barros
Fernandes, R.V. & Borges, S.V. 2019. The use of different temperatures and
inulin: Whey protein isolate ratios in the spray drying of beetroot juice. Journal
of Food Processing and Preservation 43(10): e14113.
Du, J., Ge, Z.Z., Xu, Z., Zou, B.,
Zhang, Y. & Li, C.M. 2014. Comparison of the efficiency of five different
drying carriers on the spray drying of persimmon pulp powders. Drying
Technology 32(10): 1157-1166.
Ehiem, J.C., Ifeanyichukwu, V.,
Ndirika, O., Onwuka, U.N. & Raghavan, V. 2019. The moisture-dependent flow
characteristics of Canarium schweinfurthii Engler nuts. Research in
Agricultural Engineering 65(2): 40-47.
Elias, H.S., Baharum, S.N., Azizan,
K.A., Ahmad, W.Y.W., Chandren, S. & Basar, N. 2023. Optimization of
ultrasound-assisted extraction for antioxidant activity in relation to
rhoifolin content of Fortunella polyandra using Response Surface
Methodology (RSM). Sains Malaysiana 52(1): 153-164.
Figgis, B., Nouviaire, A.,
Wubulikasimu, Y., Javed, W., Guo, B., Ait-mokhtar, A., Ahzi, S., Rémond, Y.
& Ennaoui, A. 2018. Investigation of factors affecting condensation on
soiled PV modules. Solar Energy 159: 488-500.
Gianfrancesco, A., Kockel, T. &
Palzer, S. 2014. Achieving food products performance by mastering the drying
process. International Drying Symposium, Lyon, France.
Goula, A.M. & Adamopoulos, K.G.
2010. A new technique for spray drying orange juice concentrate. Innovative
Food Science and Emerging Technologies 11(2): 342-351.
Haslaniza, H., Maskat, M.Y., Wan
Aida, W.M., Mamot, S. & Saadiah, I. 2013. Optimization of enzymatic
hydrolysis of cockle (Anadara granosa) meat wash water precipitate for
the development of seafood flavor. International Food Research Journal 20(6): 3053-3059.
Isa, N., Sofian Seng, N.S., Wan
Mustapha, W.A., Markom, M. & Mohd Azhari, N.A. 2022. Pengoptimuman
pengekstrakan lemak biji jeruk mangga (Mangifera indica L.) menggunakan
Kaedah Respons Permukaan dan analisis lipid. Sains Malaysiana 51(8):
2713-2724.
Leyva-Porras, C., Saavedra-Leos,
M.Z., Cervantes-González, E., Aguirre-Bañuelos, P., Silva-Cázarez, M.B. &
Álvarez-Salas, C. 2019. Spray drying of blueberry juice-maltodextrin mixtures:
Evaluation of processing conditions on content of resveratrol. Antioxidants 8(10): 437.
Liu, C.Z., Wu, J.Q., Ren, L.Q., Tong,
J., Li, J.Q., Cui, N., Brown, N.M.D. & Meenan, B.J. 2004. Comparative study
on the effect of RF and DBD plasma treatment on PTFE surface modification. Materials
Chemistry and Physics 85(2-3): 340-346.
Liu, X., Gao, C., Fu, C., Xi, Y.,
Fatehi, P., Zhao, J.R., Wang, S., Gibril, M.E. & Kong, F. 2022. Preparation
and performance of lignin-based multifunctional superhydrophobic coating. Molecules 27(4): 1440.
Lojen, D., Zaplotnik, R., Primc, G.,
Mozetič, M. & Vesel, A. 2022. Optimization of surface wettability of
polytetrafluoroethylene (PTFE) by precise dosing of oxygen atoms. Applied
Surface Science 598: 153817.
Mamat, N. & Razali, S.F.M. 2023.
Comparisons of various imputation methods for incomplete water quality data: A
case study of the Langat River, Malaysia. Jurnal Kejuruteraan 35(1):
191-201.
Moghaddam, A.D., Pero, M. &
Askari, G.R. 2017. Optimizing spray drying conditions of sour cherry juice
based on physicochemical properties, using response surface methodology (RSM). Journal
of Food Science and Technology 54(1): 174-184.
Mohd Yusof, M.J., Mohd Tahir, N.A.,
Firdaus, F. & M. Yusoff, S.F. 2018. Pengoptimuman parameter untuk penurunan
diimida getah asli cecair dalam sistem hidrazin hidrat/hidrogen peroksida
menggunakan Kaedah Rangsangan Permukaan (RSM). Sains Malaysiana 47(9):
2055-2061.
Movahhed, M.K. & Mohebbi, M.
2016. Spray drying and process optimization of carrot-celery juice. Journal
of Food Processing and Preservation 40(2): 212-225.
Muzaffar, K., Nayik, G.A. &
Kumar, P. 2015. Stickiness problem associated with spray drying of sugar and acid
rich foods: A mini review. Journal of Nutrition & Food Sciences S12:
003.
Navarrete-Solis, A., Hengl, N.,
Ragazzo-Sánchez, J.A., Baup, S., Calderón-Santoyo, M., Pignon, F.,
López-García, U.M. & Ortiz-Basurto, R.I. 2020. Rheological and
physicochemical stability of hydrolyzed jackfruit juice (Artocarpus
heterophyllus L.) processed by spray drying. Journal of Food Science and
Technology 57(2): 663-672.
Ohkubo, Y., Shibahara, M., Nagatani,
A., Honda, K., Endo, K. & Yamamura, K. 2018. Comparison between adhesion
properties of adhesive bonding and adhesive-free adhesion for heat-assisted
plasma-treated polytetrafluoroethylene (PTFE). The Journal of Adhesion 96(8): 776-796.
Oliveira, D.M., Clemente, E. & da Costa, J.M.C. 2014. Hygroscopic behavior and degree of caking of grugru palm (Acrocomia aculeata) powder. Journal of Food Science and Technology 51(10): 2783-2789. Othman, Z. S., Hassan, N. H. & Zubairi, S. I. 2017. Response surface optimization of rotenone using natural alcohol-based deep eutectic solvent as additive in the extraction medium cocktail. Journal of Chemistry 2017: 1-10.
Pui, L.P., Karim, R., Yusof, Y.A.,
Wong, C.W. & Ghazali, H.M. 2020. Optimization of spray-drying parameters
for the production of ‘Cempedak’ (Artocarpus integer) fruit powder. Journal
of Food Measurement and Characterization 14(6): 3238-3249.
Ramlan, N., Zamri, N.W.M., Maskat,
M.Y., Mohd, M.S., Hoong, C.O., Theng, L.Y. & Zubairi, S.I. 2018. Effect of
plasma treatment (He/CH4) on the glass surface for the reduction of
powder flux adhesion in the spray drying process. Sains Malaysiana 47(6): 1147-1155.
Ramlan, N., Zubairi, S.I. &
Maskat, M.Y. 2022. Response surface optimisation of polydimethylsiloxane (PDMS)
on borosilicate glass and stainless steel (SS316) to increase hydrophobicity. Molecules 27(11) : 3388.
Rondinella, A., Andreatta, F.,
Turrin, D. & Fedrizzi, L. 2021. Degradation mechanisms occurring in
PTFE-based coatings employed in food-processing applications. Coatings 11(11): 1419.
Sarabandi, K., Peighambardoust, S.H.,
Mahoonak, A.S. & Samaei, S.P. 2017. Effect of carrier types and
compositions on the production yield, microstructure and physical
characteristics of spray dried sour cherry juice concentrate. Journal of
Food Measurement and Characterization 11(4): 1602-1612.
Schlummer, M., Sölch, C., Meisel, T.,
Still, M., Gruber, L. & Wolz, G. 2015. Emission of perfluoroalkyl
carboxylic acids (PFCA) from heated surfaces made of polytetrafluoroethylene
(PTFE) applied in food contact materials and consumer products. Chemosphere 129: 46-53.
Shrivastava, A., Tripathi, A.D.,
Paul, V. & Chandra Rai, D. 2021. Optimization of spray drying parameters
for custard apple (Annona squamosa L.) pulp powder development using
response surface methodology (RSM) with improved physicochemical attributes and
phytonutrients. Lwt 151: 112091.
Sobulska, M. & Zbicinski, I.
2020. Advances in spray drying of sugar-rich products. Drying Technology 39(12): 1774-1799.
Veeramasuneni, S., Drelich, J.,
Miller, J.D. & Yamauchi, G. 1997. Hydrophobicity of ion-plated PTFE
coatings. Progress in Organic Coatings 31: 265-270.
Vidović, S.S., Vladić,
J.Z., Vaštag, Ž.G., Zeković, Z.P. & Popović, L.M. 2014.
Maltodextrin as a carrier of health benefit compounds in Satureja montana dry powder extract obtained by spray drying technique. Powder Technology 258: 209-215.
van der Wal, P. & Steiner, U.
2007. Super-hydrophobic surfaces made from Teflon. Soft Matter 3:
426-429.
Wan Azizee, W.Y.I. & Abu Tahrim,
N. 2022. Pengoptimuman penyingkiran sulfamethoxazole melalui kaedah gerak balas
permukaan menggunakan reka bentuk komposit berpusatkan muka. Sains
Malaysiana 51(12): 3995-4008.
Woo, M.W., Daud, W.R.W., Tasirin,
S.M. & Talib, M.Z.M. 2008. Effect of wall surface properties at different
drying kinetics on the deposition problem in spray drying. Drying Technology 26(1): 15-26.
Woun, L., Nordin, M., Kamil, R. &
Saleena, F. 2011. Empirical modeling for spray drying process of sticky and
non-sticky products. Procedia Food Science 1: 690-697.
Zareifard, M.R., Niakousari, M.,
Shokrollahi, Z. & Javadian, S. 2012. A feasibility study on the drying of
lime juice: The relationship between the key operating parameters of a small
laboratory spray dryer and product quality. Food and Bioprocess Technology 5(5): 1896-1906.
*Pengarang untuk surat-menyurat;
email: haslaniza@ukm.edu.my
|
|||
|
